Wireless LAN Security

6303 Barfield Road  Atlanta, GA 30328 Tel: 404.236.2600  Fax: 404.236.2626
Wireless LAN Security
802.11b and Corporate Networks
An ISS Technical White Paper
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 1
Introduction
Although a variety of wireless network technologies have or will soon reach the general business
market, wireless LANs based on the 802.11 standard are the most likely candidate to become
widely prevalent in corporate environments. Current 802.11b products operate at 2.4GHz, and
deliver up to 11Mbps of bandwidth – comparable to a standard Ethernet wired LAN in
performance. An upcoming version called 802.11a moves to a higher frequency range, and
promises significantly faster speeds. It is expected to have security concerns similar to 802.11b.
This low cost, combined with strong performance and ease of deployment, mean that many
departments and individuals already use 802.11b, at home or at work – even if IT staff and
security management administrators do not yet recognize wireless LANs as an approved
technology. This paper addresses the security concerns raised by both current and upcoming
802.11 network technologies.
Wireless LAN Business Drivers
Without doubt, wireless LANs have a high gee-whiz factor. They provide always-on network
connectivity, but don’t require a network cable. Office workers can roam from meeting to meeting
throughout a building, constantly connected to the same network resources enjoyed by wired,
desk-bound coworkers. Home or remote workers can set up networks without worrying about how
to run wires through houses that never were designed to support network infrastructure.
Wireless LANS may actually prove less expensive to support than traditional networks for
employees that need to connect to corporate resources in multiple office locations. Large hotel
chains, airlines, convention centers, Internet cafes, etc., see wireless LANs as an additional
revenue opportunity for providing Internet connectivity to their customers. Wireless is a more
affordable and logistically acceptable alternative to wired LANs for these organizations. For
example, an airline can provide for-fee wireless network access for travelers in frequent flyer
lounges – or anywhere else in the airport.
Market maturity and technology advances will lower the cost and accelerate widespread adoption
of wireless LANs. End-user spending, the primary cost metric, will drop from about $250 in 2001
to around $180 in 2004 (Gartner Group). By 2005, 50 percent of Fortune 1000 companies will
have extensively deployed wireless LAN technology based on evolved 802.11 standards (0.7
probability). By 2010, the majority of Fortune 2000 companies will have deployed wireless LANs
to support standard, wired network technology LANs (0.6 probability).
Reality Check
For the foreseeable future wireless technology will complement wired connectivity in enterprise
environments. Even new buildings will continue to incorporate wired LANs. The primary reason is
that wired networking remains less expensive than wireless. In addition, wired networks offer
greater bandwidth, allowing for future applications beyond the capabilities of today’s wireless
systems.
Although it may cost 10 times more to retrofit a building for wired networking (initial construction
being by far the preferred time to set up network infrastructure), wiring is only a very small fraction
of the cost of the overall capital outlay for an enterprise network. For that reason, many
corporations are only just testing wireless technology. This limited acceptance at the corporate
level means few access points with a limited number of users in real world production
environments, or evaluation test beds sequestered in a lab. In response, business units and
individuals will deploy wireless access points on their own. These unauthorized networks almost
certainly lack adequate attention to information security, and present a serious concern for
protecting online business assets.
Finally, the 802.11b standard shares unlicensed frequencies with other devices, including
Bluetooth wireless personal area networks (PANs), cordless phones, and baby monitors. These
technologies can, and do, interfere with each other. 802.11b also fails to delineate roaming
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 2
(moving from one cell to another), leaving each vendor to implement a different solution. Future
proposals in 802.11 promise to address these shortcomings, but no shipping products are on the
immediate horizon.
Wireless Security In The Enterprise
802.11b’s low cost of entry is what makes it so attractive. However, inexpensive equipment also
makes it easier for attackers to mount an attack. “Rogue” access points and unauthorized, poorly
secured networks compound the odds of a security breach.
The following diagram depicts an intranet or internal network that is properly configured to handle
wireless traffic, with two firewalls in place, plus intrusion detection and response sensors to
monitor traffic on the wireless segment. One firewall controls access to and from the Internet. The
other controls access to and from the wireless access point. The access point itself is the bridge
that connects mobile clients to the internal network.
The access point has a dedicated IP address for remote management via SNMP (Simple
Network Management Protocol). The wireless clients themselves – usually laptops or desktops
and handhelds – may also use SNMP agents to allow remote management. As a result, each of
these devices contains a sensor to ensure that each unit is properly configured, and that these
configurations have not been improperly altered. The network itself is regularly monitored to
identify access points in operation, and verify that they are authorized and properly configured.
While this paper focuses on the risk issues from a corporate network perspective, these same
issues apply to home networks, telecommuters using wireless, and “public use” networks such as
those being set up by Microsoft to allow wireless Internet access at select Starbucks locations.
Remote users are now able to access internal corporate resources from multiple types of foreign
networks. Even organizations without internal wireless networks must take wireless into account
as part of their overall security practices.
Known Risks
Although attacks against 802.11b and other wireless technologies will undoubtedly increase in
number and sophistication over time, most current 802.11b risks fall into seven basic categories:
Insertion attacks
Interception and unauthorized monitoring of wireless traffic
Jamming
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 3
Client-to-Client attacks
Brute force attacks against access point passwords
Encryption attacks
Misconfigurations
Note that these classifications can apply to any wireless technology, not just 802.11b.
Understanding how they work and using this information to prevent their success is a good
stepping stone for any wireless solution.
Insertion Attacks
Insertion attacks are based on deploying unauthorized devices or creating new wireless networks
without going through security process and review.
Unauthorized Clients – An attacker tries to connect a wireless client, typically a laptop or PDA,
to an access point without authorization. Access points can be configured to require a
password for client access. If there is no password, an intruder can connect to the internal
network simply by enabling a wireless client to communicate with the access point. Note,
however, that some access points use the same password for all client access, requiring all
users to adopt a new password every time the password needs to be changed.
Unauthorized or Renegade Access Points – An organization may not be aware that internal
employees have deployed wireless capabilities on their network. This lack of awareness could
lead to the previously described attack, with unauthorized clients gaining access to corporate
resources through a rogue access point. Organizations need to implement policy to ensure
secure configuration of access points, plus an ongoing process in which the network is scanned
for the presence of unauthorized devices.
Interception and Monitoring of Wireless Traffic
As in wired networks, it is possible to intercept and monitor network traffic across a wireless LAN.
The attacker needs to be within range of an access point (approximately 300 feet for 802.11b) for
this attack to work, whereas a wired attacker can be anywhere where there is a functioning
network connection. The advantage for a wireless interception is that a wired attack requires the
placement of a monitoring agent on a compromised system. All a wireless intruder needs is
access to the network data stream.
There are two important considerations to keep in mind with the range of 802.11b access points.
First, directional antennae can dramatically extend either the transmission or reception ranges of
802.11b devices. Therefore, the 300 foot maximum range attributed to 802.11b only applies to
normal, as-designed installations. Enhanced equipment also enhances the risk. Second, access
points transmit their signals in a circular pattern, which means that the 802.11b signal almost
always extends beyond the physical boundaries of the work area it is intended to cover. This
signal can be intercepted outside buildings, or even through floors in multistory buildings. Careful
antenna placement can significantly affect the ability of the 802.11b signal to reach beyond
physical corporate boundaries.
Wireless Packet Analysis – A skilled attacker captures wireless traffic using techniques
similar to those employed on wired networks. Many of these tools capture the first part of the
connection session, where the data would typically include the username and password. An
intruder can then masquerade as a legitimate user by using this captured information to hijack
the user session and issue unauthorized commands.
Broadcast Monitoring – If an access point is connected to a hub rather than a switch, any
network traffic across that hub can be potentially broadcasted out over the wireless network.
Because the Ethernet hub broadcasts all data packets to all connected devices including the
wireless access point, an attacker can monitor sensitive data going over wireless not even
intended for any wireless clients.
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 4
Access Point Clone (Evil Twin) Traffic Interception – An attacker fools legitimate wireless
clients into connecting to the attacker’s own network by placing an unauthorized access point
with a stronger signal in close proximity to wireless clients. Users attempt to log into the
substitute servers and unknowingly give away passwords and similar sensitive data.
Jamming
Denial of service attacks are also easily applied to wireless networks, where legitimate traffic can
not reach clients or the access point because illegitimate traffic overwhelms the frequencies. An
attacker with the proper equipment and tools can easily flood the 2.4 GHz frequency, corrupting
the signal until the wireless network ceases to function. In addition, cordless phones, baby
monitors and other devices that operate on the 2.4 GHz band can disrupt a wireless network
using this frequency. These denials of service can originate from outside the work area serviced
by the access point, or can inadvertently arrive from other 802.11b devices installed in other work
areas that degrade the overall signal.
Client-to-Client Attacks
Two wireless clients can talk directly to each other, bypassing the access point. Users therefore
need to defend clients not just against an external threat but also against each other.
File Sharing and Other TCP/IP Service Attacks – Wireless clients running TCP/IP services
such as a Web server or file sharing are open to the same exploits and misconfigurations as
any user on a wired network.
DOS (Denial of Service) – A wireless device floods other wireless client with bogus packets,
creating a denial of service attack. In addition, duplicate IP or MAC addresses, both intentional
and accidental, can cause disruption on the network.
Brute Force Attacks Against Access Point Passwords
Most access points use a single key or password that is shared with all connecting wireless
clients. Brute force dictionary attacks attempt to compromise this key by methodically testing
every possible password. The intruder gains access to the access point once the password is
guessed.
In addition, passwords can be compromised through less aggressive means. A compromised
client can expose the access point. Not changing the keys on a frequent basis or when
employees leave the organization also opens the access point to attack. Managing a large
number of access points and clients only complicates this issue, encouraging lax security
practices.
Attacks against Encryption
802.11b standard uses an encryption system called WEP (Wired Equivalent Privacy). WEP has
known weaknesses (see http://www.isaac.cs.berkeley.edu/isaac/wep-faq.html for more
information), and these issues are not slated to be addressed before 2002. Not many tools are
readily available for exploiting this issue, but sophisticated attackers can certainly build their own.
Misconfiguration
Many access points ship in an unsecured configuration in order to emphasize ease of use and
rapid deployment. Unless administrators understand wireless security risks and properly
configure each unit prior to deployment, these access points will remain at a high risk for attack or
misuse. The following section examines three leading access points, one each from Cisco,
Lucent and 3Com. Although each vendor has its own implementation of 802.11b, the underlying
issues should be broadly applicable to products from other vendors.
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 5
Server Set ID (SSID) – SSID is a configurable identification that allows clients to communicate
with an appropriate access point. With proper configuration, only clients with the correct SSID
can communicate with access points. In effect, SSID acts as a single shared password
between access points and clients. Access points come with default SSIDs. If not changed,
these units are easily compromised. Here are common default passwords:
“tsunami” – Cisco
”101” – 3Com
“RoamAbout Default Network Name” – Lucent/Cabletron
“Compaq” – Compaq
“WLAN” – Addtron
“intel” – Intel
“linksys” – Linksys
“Default SSID”, “Wireless” – Other manufacturers
SSIDs go over the air as clear text if WEP is disabled, allowing the SSID to be captured by
monitoring the network’s traffic. In addition, the Lucent access points can operate in Secure
Access mode. This option requires the SSID of both client and access point to match. By
default this security option is turned off. In non-secure access mode, clients can connect to the
access point using the configured SSID, a blank SSID, or an SSID configured as “any.”
Wired Equivalent Privacy (WEP) – WEP can be typically configured as follows:
No encryption
40 bit encryption
128 bit encryption
Most access points ship with WEP turned off. Although 128 bit encryption is more effective than
40 bit encryption, both key strengths are subject to WEP’s known flaws.
SNMP Community Passwords – Many wireless access points run SNMP agents. If the
community word is not properly configured, an intruder can read and potentially write sensitive
data on the access point. If SNMP agents are enabled on the wireless clients, the same risk
applies to them as well.
By default, many access points are read accessible by using the community word, “public”.
3Com access points allow write access by using the community word, ”comcomcom”. Cisco
and Lucent/Cabletron require the write community word to be configured by the user or
administrator before the agent is enabled.
Configuration Interfaces – Each access point model has its own interface for viewing and
modifying its configuration. Here are the current interface options for these three access points:
Cisco – SNMP, serial, Web, telnet
3Com – SNMP, serial, Web, telnet
Lucent / Cabletron – SNMP, serial (no web/telnet)
3Com access points lack access control to the Web interface for controlling configuration. An
attacker who locates a 3Com access point Web interface can easily get the SSID from the
“system properties” menu display. 3Com access points do require a password on the Web
interface for write privileges. This password is the same as the community word for write
privileges, therefore 3Com access points are at risk if deployed using the default “comcomcom”
as the password.
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 6
Client Side Security Risk – Clients connected to an access point store sensitive information
for authenticating and communicating to the access point. This information can be
compromised if the client is not properly configured. Cisco client software stores the SSID in the
Windows registry, and the WEP key in the firmware, where it is more difficult to access.
Lucent/Cabletron client software stores the SSID in the Windows registry. The WEP key is
stored in the Windows registry, but it is encrypted using an undocumented algorithm. 3Com
client software stores the SSID in the Windows registry. The WEP key is stored in the Windows
registry with no encryption.
Installation – By default, all three access points are optimized to help build a useful network as
quickly and as easily as possible. As a result, the default configurations minimize security.
Wireless Information Security Management
Process and technology are always easily confused, and never more so than with wireless
information security management. In fact, the same business processes that establish strong risk
management practices for physical assets and wired networks also work to protect wireless
resources. The following cost-effective guidelines help enable organizations to establish proper
security protections as part of an overall wireless strategy – and will continue to work in spite of
wireless networking’s rapid evolution. The following items are an introduction to this approach.
Wireless Security Policy and Architecture Design – Security policy, procedures and best
practices should include wireless networking as part of an overall security management
architecture to determine what is and is not allowed with wireless technology.
Treat Access Points As Untrusted – Access points need to be identified and evaluated on a
regular basis to determine if they need to be quarantined as untrusted devices before wireless
clients can gain access to internal networks. This determination means appropriate placement of
firewalls, virtual private networks (VPN), intrusion detection systems (IDS), and authentication
between access point and intranets or the Internet.
Access Point Configuration Policy – Administrators need to define standard security settings
for any 802.11b access point before it can be deployed. These guidelines should cover SSID,
WEP keys and encryption, and SNMP community words.
Access Point Discovery – Administrators should regularly search outwards from a wired
network to identify unknown access points. Several methods of identifying 802.11b devices exist,
including detection via banner strings on access points with either Web or telnet interfaces.
Wireless network searches can identify unauthorized access points by setting up a 2.4 GHz
monitoring agent that searches for 802.11b packets in the air. These packets may contain IP
addresses that identify which network they are on, indicating that rogue access points are
operating in the area. One important note: this process may pick up access points from other
organizations in densely populated areas.
Access Point Security Assessments – Regular security audits and penetration assessments
quickly identify poorly configured access points, default or easily guessed passwords and
community words, and the presence or absence of encryption. Router ACLs and firewall rules
also help minimize access to the SNMP agents and other interfaces on the access point.
Wireless Client Protection – Wireless clients need to be regularly examined for good security
practices. These procedures should include the presence of some or all of the following:
Distributed personal firewalls to lock down access to the client
VPNs to supplement encryption and authentication beyond what 802.11b can provide
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 7
Intrusion detection and response to identify and minimize attacks from intruders, viruses,
Trojans and backdoors
Desktop assessments to identify and repair security issues on the client device
Managed Security Services for Wireless – Managed Security Services (MSS) helps
organizations establish effective security practices without the overhead of an extensive, in-house
solution. MSS providers handle assessment, design, deployment, management and support
across a broad range of information security disciplines. This 24/7/365 solution works with the
customer to set policy and architecture, plus provides emergency response, if needed. These
services help an organization operating wireless networks to:
Deploy firewalls that separate wireless networks from internal networks or the Internet
Establish and monitor VPN gateways and VPN wireless clients
Maintain an intrusion detection system on the wireless network to identify and respond to
attacks and misuse before critical digital resource are placed at risk.
Internet Security Systems Wireless LAN Solutions
Internet Security Systems products and services provide a robust security management solution
for wireless LANs. These rapidly expanding offerings encompass:
Security Software Products – Internet Security Systems’ security products already protect
wireless LAN environments against known security risks. ISS’ Internet Scanner™ network
vulnerability assessment product probes networks to detect unauthorized or poorly configured
wireless access points, as represented in the diagram below.
The RealSecure™ Protection System, deployed between a wireless access point and the
corporate network, recognizes and reacts to attacks and misuse directed over the wireless LAN
(below). In addition, ISS’ renowned X-Force™ research and development team continually
update these products.
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 8
Managed Security Services – Internet Security Systems’ Managed Security Services protect
wireless LANS on a 24×7 basis through remote network assessments and tactical deployment of
remotely managed intrusion protection services. As new wireless protections are added to ISS
security products, Managed Security Services will deliver these additional capabilities to our
customers.
Security Architecture Consulting – Internet Security Systems’ Consulting Solutions Group has
in-depth security knowledge, expertise, and proven methodology required that helps
organizations assess, integrate, design, and configure their wireless LANs and surrounding
security infrastructure.
Wireless LAN Security Education – Internet Security Systems’ SecureU™ education services
organization has developed wireless LAN security content to help customers understand the
nuances of wireless LAN security and establish valid defensive techniques to minimize security
risks.
Product Updates – Internet Security Systems’ X-Force research and development team
continually adds product enhancements that deliver new protections against wireless LAN risks.
These X-Press Update™ enhancements quickly and easily integrate into existing product
installations.
WWireWireless Lan Security 802.11b Wireless LAN Security
An ISS Technical White Paper Page 9
About Internet Security Systems (ISS)
Founded in 1994, Internet Security Systems (ISS) (Nasdaq: ISSX) is a world leader in software
and services that protect critical online resources from attack and misuse. ISS is headquartered
in Atlanta, GA, with additional operations throughout the United States and in Asia, Australia,
Europe, Latin America and the Middle East.
Copyright © 2001 Internet Security Systems, Inc. All rights reserved worldwide.
Internet Security Systems, the Internet Security Systems logo, Internet Scanner, RealSecure, SecureU, XForce
and X-Press Update are trademarks of Internet Security Systems, Inc. Other trademarks and trade
names mentioned are marks and names of their owners as indicated. All trademarks are the property of their
respective owners and are used here in an editorial context without intent of infringement. Specifications are
subject to change without notice.

Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s

%d blogger menyukai ini: